What is a roof bulkhead? Why it adds height but not a storey

A weathered metal water tank on stilts atop a rooftop, with antenna mounts and equipment visible below it.

Pull up a candidate building on imagery and measure roof height against the parcel's listed floor count, and the numbers will not line up. A building with a 9-storey footprint shows up 12 to 15 feet taller than 9 floors at typical slab-to-slab heights would suggest. That gap is usually a bulkhead, and understanding it matters before anyone quotes an antenna mounting height off a desktop review.

Roof bulkhead, defined

A roof bulkhead is the small enclosed structure sitting on top of a flat or low-slope roof, housing the stairwell head, mechanical equipment, or both. It is not occupied space in the way a storey is. Nobody has a lease on a bulkhead. Building codes generally don't count it toward storey totals or in some jurisdictions even toward maximum building height, because it's classified as an accessory structure, not habitable floor area.

Picture the stairwell that lets maintenance staff and tenants reach the roof. That stairwell has to terminate somewhere above the last occupied floor, and that termination point is the bulkhead. Same logic applies to elevator overrun, the shaft space above the top landing that houses the hoist machinery, cables, and the buffer the car needs to stop safely. Both get built as small rooftop boxes, both add real vertical feet, and neither shows up as a storey on the certificate of occupancy or the assessor's record.

For a site-acq planner, this is the gap between the height a zoning database implies and the height sitting on the roof right now. Pull a county record that says "9 stories," and the rooftop parapet could be anywhere from 95 to 140 feet depending on floor-to-floor heights and whatever's stacked on top. The bulkhead, the stair tower, and any mechanical penthouse all sit in that gap.

Stair tower, elevator overrun, and penthouse: not the same thing

These three terms get used loosely on site, so it's worth separating them before a candidate goes into the RF plan.

A rooftop stair tower is the bulkhead specific to stair access. It's typically the smallest of the three, often just a doorway-sized enclosure with a sloped or flat roof, rising maybe 8 to 12 feet above the main roof deck.

Elevator overrun height runs a bit taller, usually 10 to 16 feet, because it has to clear the hoist machine, the cables, and code-required buffer clearance above the top floor the elevator serves. On older buildings with hydraulic elevators, the overrun can be shorter or nearly absent since the machine room sits below grade instead.

A penthouse is a different animal. Where a bulkhead is a utility box, a penthouse is a mechanical or storage structure, often large enough to walk through, housing HVAC units, water tanks, or building-wide mechanical systems. Penthouses can add considerably more height than a bare bulkhead, sometimes a full extra 15 to 20 feet, and they're often the structure a prospective rooftop lease is actually negotiating access around. Some jurisdictions treat a penthouse differently in zoning calculations too, depending on its footprint relative to the roof below.

The practical takeaway: when a rooftop candidate reads as one height in a database and a different height on an elevation photo, the delta is probably sitting in one of these three structures. That distinction decides whether the gap is a stairwell door, mechanical equipment that might need relocating, or a penthouse to route cable around.

Why this matters before a truck rolls

None of this changes how many floors a building has for leasing purposes. It changes the actual top-of-parapet elevation, which is what matters for coax runs, ice bridge routing, and line-of-sight to the next node. A 9-storey building that reads as 95 feet to the bulkhead-topped parapet and 110 feet including the penthouse behind it are two different RF problems, and both numbers matter for different reasons on the same site.

Storey Estimation turns VHR stereo or shadow-derived rooftop height into a per-building storey estimate you can sanity-check against zoning records before a surveyor ever gets dispatched. If a candidate's implied height doesn't match its listed floor count, that's worth flagging early, and this is a straightforward way to catch it from the desk.

Get started

← Back to the blog